GVM, payload and truck licence classes

GVM and payload explained with a real truck comparison, Victorian licence classes and the mass limits to check before you order.

10 min readUpdated 17 November 2026Reviewed by Jason Cugley

The short answer

GVM and payload tell you the truck’s approved loaded ceiling and its carrying capacity.

  1. 01

    People, fuel and fittings all use that capacity.

  2. 02

    In Victoria, a car licence covers a truck with GVM no greater than 4.5 tonnes; above that, the required heavy vehicle class depends on GVM, axles and trailer configuration.⁠[1]⁠[2]

  3. 03

    Read the recorded rating, then subtract the weight of the finished truck and everything travelling with it before allowing for cargo.

Key takeaways

  1. Put the exact GVM rating on the order before choosing who will drive the truck.

  2. Get a completed-vehicle weight with the body fitted, and record the fuel and equipment included.

  3. Ask for loaded axle weights as well as a whole-vehicle weight.

  4. Include the trailer and coupling loads in the written brief if you intend to tow.

  5. Check the licences of relief drivers before choosing the higher rating.

Read the rating before the first load

You’re on the weighbridge for the truck’s first loaded run, with room still showing on the tray. The ticket needs to fit the truck’s approved rating, regardless of how much floor you can still see.

Start at the manufacturer’s plate, often near the doorway on a cab-over truck, then match the vehicle identification number to its records.⁠[17] The rating affects what you can carry, who can drive and which heavy vehicle rules apply.⁠[1]⁠[5] A badge won’t settle that.

For newer vehicles, check the Register of Approved Vehicles [RAV], the online compliance record searched by VIN. It replaced the former compliance-plate system, although some heavy vehicles still require physical vehicle plates; the RAV includes a GVM field, with requirements varying by vehicle category.⁠[6] Check any modification certificate and the current registration record as well. Ask the supplier to resolve a mismatch in writing before delivery.⁠[13]⁠[14]

GVM and payload: count everything aboard

Gross vehicle mass [GVM] is the approved maximum loaded mass of the truck, specified by the registration authority or otherwise by the manufacturer.⁠[5] Tare is its unoccupied, unloaded mass with fitted equipment and operating fluids, but only 10 litres of fuel under the HVNL definition.⁠[17] Payload is the weight available above the stated empty-vehicle baseline, so check what that baseline includes before treating it as cargo capacity.⁠[15]

Gross combination mass [GCM] is the approved maximum loaded mass of the truck and its trailers together.⁠[15] An axle limit is the maximum permitted mass carried by an axle or axle group, subject to both component ratings and legal limits.⁠[8]

For a cargo budget, use: cargo left = GVM minus completed tare minus people minus extra fuel minus anything added after weighing. If a toolbox is already in tare, don’t subtract it again. If the weighbridge ticket includes a full tank, don’t add another full tank either.

A crane needs mounting steel and hydraulics. A tail lift brings its mounting gear, and sometimes extra batteries. Ask for installed weights, then weigh the completed truck; the weight of the attachment alone doesn’t describe the installation. Compare body choices in tipper, tray or pantech before the body order fixes the mass budget.

Compare the same truck across the car-licence line

Worked example

A building business choosing two ratings of a Hino 616

Assume a building business wants an automatic alloy-tray truck for tools and materials, with a passenger travelling most days. The real model is Hino’s 300 Series 616 AT 3375 STD Alloy Tray. Its September 2026 sheet lists a standard GVM of 4,499 kg and an optional 5,500 kg rating, with GCMs of 7,999 kg and 9,000 kg respectively.⁠[7]

Hino makes the 4,499 kg rating conditional on meeting the ADR goods-vehicle definition.⁠[7] Confirm the proposed build qualifies. Its sheet lists indicative chassis mass, so we use an assumed completed tare of 3,000 kg, including the tray, standard equipment, operating fluids and 10 litres of fuel. This isn’t a measured or manufacturer-guaranteed tare.

All additions below are assumptions. Fuel is topped up to the model’s listed 100-litre capacity:⁠[7] [100 minus 10] litres × an assumed 0.84 kg per litre = 75.6 kg. The driver and passenger are allowed 90 kg and 80 kg; specified fitting allowances include their mounting hardware.

ItemCar licenceLight rigid
Plate GVM to order⁠[7]4,499 kg5,500 kg
Completed tare, assumed3,000 kg3,000 kg
Driver, assumed90 kg90 kg
Passenger, assumed80 kg80 kg
Extra fuel, calculated75.6 kg75.6 kg
Bull bar, assumed60 kg60 kg
Toolboxes, assumed120 kg120 kg
Rack, assumed40 kg40 kg
Additions above tare90 + 80 + 75.6 + 60 + 120 + 40 = 465.6 kg90 + 80 + 75.6 + 60 + 120 + 40 = 465.6 kg
Ready for cargo3,000 + 465.6 = 3,465.6 kg3,000 + 465.6 = 3,465.6 kg
Cargo mass ceiling4,499 minus 3,465.6 = 1,033.4 kg5,500 minus 3,465.6 = 2,034.4 kg
Minimum Victorian licence⁠[1]⁠[2]CarLR

Choosing the car-licence rating costs 1,001 kg of cargo capacity: 2,034.4 minus 1,033.4 = 1,001 kg. It lets car-licensed staff drive; the higher rating requires LR or a higher suitable class.⁠[1]⁠[2] Obtain prices for both ratings and any training before comparing the purchase cost. No price difference is assumed here.

These are GVM ceilings, subject to axle, tyre and other limits.⁠[8] The decimal places show the calculation, not weighbridge accuracy. Replace the assumed tare and fittings with measured weights before setting the loading instruction, and allow room for the gear your crew adds over time.

Fittings reduce cargo capacity one at a time On the same 4499 kilogram truck, 1253.4 kilograms remains after the assumed completed tare, occupants and fuel. A 60 kilogram bull bar reduces that to 1193.4, 120 kilograms of toolboxes reduces it to 1073.4, and a 40 kilogram rack leaves 1033.4 kilograms. The fittings arrive in order and the counter changes in discrete steps. All fitting weights are assumptions. WHAT EATS PAYLOAD Same truck | assumed fitting weights Bull bar 60 kg Toolboxes 120 kg Rack 40 kg CARGO CAPACITY LEFT 1,253.4 kg People and fuel already counted 1,193.4 kg After the bull bar 1,073.4 kg After the toolboxes 1,033.4 kg After the rack Every fitted kilogram takes a kilogram from the cargo allowance.
Fig. 2Assumed fittings arrive on the same truck while its remaining cargo capacity counts down in steps.

Truck licence classes in Victoria

These are the Victorian class boundaries and ordinary minimum holding periods checked on 17 November 2026. Austroads uses the national class framework; Transport Victoria sets out the local eligibility requirements.⁠[2]⁠[4] The ladder shows vehicle classes, not compulsory training steps.

ClassVehicle entitlementVictorian holding period before assessment
CarGVM at most 4.5 t; seating for at most 12 adults including driver.⁠[1]Existing car licence.
LRGVM above 4.5 t through 8 t; also vehicles seating over 12 adults with GVM at most 8 t.⁠[2]⁠[4]Australian car licence: at least 12 months.⁠[2]
MRGVM above 8 t, with no more than 2 axles.⁠[4]Australian car licence: at least 12 months.⁠[2]
HRGVM above 8 t, with at least 3 axles, including lifted axles; also articulated buses.⁠[2]⁠[4]Australian car licence: at least 24 months.⁠[2]
HCPrime mover with one semitrailer above 9 t GVM, or rigid with a trailer above 9 t GVM; either may include an unladen converter dolly.⁠[2]Australian MR or HR licence: at least 12 months.⁠[2]
MCAny motor vehicle or combination except motorcycles, including multiple-trailer combinations.⁠[2]⁠[4]Australian HR or HC licence: at least 12 months; HR holders pass HC assessment before MC training.⁠[2]

LR, MR and HR include lower-class entitlements. Each permits a single trailer up to 9 tonnes GVM, with semitrailers excluded from the MR and HR towing entitlement. Vehicle ratings still apply.⁠[2]⁠[4] Victoria also permits car-licence holders to tow one trailer up to 9 tonnes GVM or the manufacturer’s limit, whichever is lower.⁠[1]

To step up, hold a current Victorian car licence and satisfy the relevant holding period. Complete eyesight and knowledge testing, on-road and off-road assessments through an accredited provider, and meet the medical requirements. HC and MC applicants also need formal training.⁠[3] Check transmission restrictions on the actual licence before allocating a truck.

Victorian truck licence ladder Six steps show car, light rigid, medium rigid, heavy rigid, heavy combination and multi combination. The key dividing lines are 4.5 tonnes GVM, 8 tonnes GVM, axle count and trailer configuration. This is a vehicle-class ladder, not a requirement to obtain each class in turn. The adjacent table gives Victorian eligibility and towing details. VICTORIA: LICENCE CLASSES Vehicle classes | 17 November 2026 C CAR GVM no more than 4.5 t Up to 12 adults, driver included LR LIGHT RIGID GVM over 4.5 t, up to 8 t Or over 12 adults, GVM up to 8 t MR MEDIUM RIGID GVM over 8 t No more than 2 axles HR HEAVY RIGID GVM over 8 t 3 or more axles HC HEAVY COMBINATION Single trailer over 9 t GVM See prime mover and rigid rules MC MULTI COMBINATION Includes multiple trailers Any motor vehicle except motorcycles Class details and eligibility are in the table.
Fig. 3The Victorian vehicle-class steps separate GVM, axle count and trailer configuration, with full entitlements in the table.⁠[1]⁠[2]⁠[4]

Where heavy vehicle and fatigue rules begin

Under the Heavy Vehicle National Law [HVNL], a vehicle becomes heavy above 4.5 tonnes GVM, or above 4.5 tonnes aggregate trailer mass for a trailer. Aggregate trailer mass is the trailer’s rated total, including mass supported at the hitch.⁠[17] A combination containing a heavy vehicle also qualifies.⁠[5] Exactly 4.5 tonnes is outside that definition.⁠[5]

For ordinary goods trucks, prescribed work and rest rules apply above 12 tonnes GVM. For combinations, the law adds the vehicles’ GVMs; it doesn’t use the cargo actually aboard.⁠[9] The prescribed threshold remains 12 tonnes as at November 2026.⁠[10] Buses above 4.5 tonnes GVM built or fitted to carry more than 12 adults including the driver have their own fatigue-regulated category.⁠[9]

A driver of a fatigue-regulated vehicle doing standard-hours work outside a 100 km radius of base needs a work diary. This is a radius, not kilometres accumulated during the day. Alternative Compliance Hours, transitional BFM or AFM, and exemption hours require a diary regardless of distance, subject to applicable exemptions.⁠[9]

Local standard-hours drivers still need work and rest records. Diary carriage requirements also look back over the previous 28 days.⁠[5] Since 1 August 2026, the duty against driving fatigued or unfit applies across heavy vehicles, including trucks below the fatigue-regulated threshold.⁠[9]⁠[16] Our 5,500 kg rigid therefore doesn’t trigger prescribed work hours by itself, but its driver still has that duty.

Check axle loads and towing separately

A whole-truck reading cannot show how much sits on each axle. Ask for axle weights with the heaviest intended load in its actual position. Putting dense material at the back can exhaust the rear axle allowance before the truck reaches GVM; moving it changes axle loading without changing total mass.⁠[8]⁠[11]

General Mass Limits [GML] set legal limits by vehicle and axle configuration. They changed on 1 August 2026, so use the current tables. Those changes don’t increase this Hino’s approved GVM, and a higher legal axle limit cannot override a lower tyre or component rating.⁠[8]⁠[16]

For towing, count the complete combination against GCM and check the truck’s GVM with the trailer attached. Hitch download uses truck capacity; weigh all axles together to avoid counting that transferred weight twice.⁠[15] The example’s ratings give a GCM difference of 7,999 minus 4,499 = 3,500 kg, or 9,000 minus 5,500 = 3,500 kg.⁠[7] That subtraction alone does not approve a trailer: towing and coupling ratings, trailer limits and axle loads must also pass.⁠[8]⁠[15]

What an overload means for the business

The HVNL mass categories are minor, substantial and severe. Critical is a fatigue breach category, not a fourth mass category.⁠[5] Under sections 97 to 100, classification uses the applicable permitted mass and the statutory rounding rules.⁠[5]

CategoryWhere it starts
MinorAbove the permitted mass but below the substantial threshold.⁠[5]
SubstantialStarts at the higher of 105% of permitted mass, rounded up to the nearest 0.1 t, and permitted mass plus 0.5 t. Continues below the severe threshold.⁠[5]
SevereStarts at 120% of permitted mass rounded upwards to the nearest 0.1 t.⁠[5]

For the 5,500 kg truck, 105% is 5,775 kg, rounded up to 5,800 kg. The permitted mass plus 0.5 t is 6,000 kg, which is higher, so a substantial breach starts at 6,000 kg. A severe breach starts at 5,500 × 1.20 = 6,600 kg. Neither figure creates an overload allowance. A smaller excess remains a breach, and an overloaded axle can breach its own limit while the whole truck passes.⁠[5]

The driver and the person permitting the truck’s use can face mass offences.⁠[5] Chain of Responsibility [CoR] is the duty framework covering businesses that control or influence heavy vehicle transport, including employers, operators, loaders and goods senders or receivers. Each party must ensure safety so far as reasonably practicable; executives have a separate due-diligence duty.⁠[11] Buying a truck with too little usable payload is a procurement decision worth fixing before it becomes a daily loading problem.

Overloading can affect an insurance claim, but automatic loss of all cover is too broad a claim. Policy wording matters, and section 54 of the Insurance Contracts Act limits refusal for certain acts after cover began, with rules about causation and prejudice to the insurer.⁠[12] Ask your insurer or insurance broker to explain the overload and driver-licence provisions in your policy, in writing.

Changing GVM requires approval

A GVM can be increased or reduced, but fitting heavier springs doesn’t approve a new rating. For a vehicle already above 4.5 tonnes before modification, NHVR’s VSG-9 requires certification by an appropriately accredited Approved Vehicle Examiner under VSB6. Manufacturer-option re-ratings require written manufacturer specifications; a dealer’s letter alone isn’t acceptable evidence.⁠[13]

In Victoria, GVM changes require a Vehicle Assessment Signatory Scheme [VASS] certificate, with certification presented to VicRoads for processing. Discuss a light-to-heavy change with the appropriate signatory before buying parts.⁠[14] If the change affects towing capability, GCM also needs assessment and certification.⁠[13]

Put the mass budget into the brief

  1. Record the heaviest routine cargo, its dimensions and where it will sit. Include the awkward job you already know the truck will do, rather than choosing from an average load.
  2. List every intended driver and their actual licence conditions. Compare the higher rating with the work available to those drivers, including holiday and sick-leave cover.
  3. Specify the required cargo allowance after the completed body, people and operating equipment. Require the supplier to state what is included in tare and identify every assumed weight.
  4. Require completed whole-vehicle and axle weighbridge figures before accepting the loading plan. Include the trailer configuration if towing, and resolve any failed limit before the first road job.
  5. Use EVRON’s See the brief we’d send. Its Compliance line covers mass, dimensions and load restraint checked against the loads you carry. We put that into the same written brief for each dealer and body builder to quote.

Questions people ask

Does GVM include payload?

GVM is the ceiling for the loaded truck, including its cargo, occupants and equipment.⁠[5]⁠[15] A 4,499 kg rating doesn’t mean you can put 4,499 kg on the tray. In the assumptions here, only 1,033.4 kg remains for cargo after the completed truck and daily additions are counted.

Does payload include the driver and fuel?

People and fuel use the truck’s available mass allowance. Check the stated baseline: statutory tare includes only 10 litres of fuel, while kerb mass usually includes a full tank.⁠[6]⁠[15] Subtract only the fuel and equipment not already included, then allow for the actual occupants.

Can I drive a 4.5-tonne truck on a car licence?

Yes, in Victoria a car licence permits a truck rated at no more than 4.5 tonnes GVM, with seating for no more than 12 adults including the driver.⁠[1] The rating is the deciding number. A higher-rated truck needs the appropriate heavy vehicle class even if you drive it empty.⁠[2]

Can a light rigid licence drive an 8-tonne truck?

Yes, a Victorian LR licence includes a rigid truck rated at exactly 8 tonnes GVM.⁠[4] Above 8 tonnes, a rigid with no more than two axles requires MR; one with three or more requires HR. Check any licence conditions and towing entitlement as well.⁠[2]⁠[4]

Is GCM the same as towing capacity?

No. GCM limits the loaded combination; towing capacity limits what the vehicle and its towing equipment can tow.⁠[15] The Hino calculation leaves 3,500 kg between GVM and GCM, but the hitch load still counts against the truck and its axle limits. Have the combination checked in its working configuration.

Can I reduce GVM to keep a car licence?

An approved reduction may be possible, but carrying less doesn’t change the rating. NHVR’s re-rating process requires certification, and Victoria requires the relevant VASS approval and registration processing.⁠[13]⁠[14] Recalculate the cargo allowance at the lower rating before proceeding; this example gives up 1,001 kg.

Run your own numbers

See the brief we’d send

Pick the vehicle: rigid truck, tipper, prime mover, van, car or SUV. The drawing and the brief change to match.

Open the tool

Sources

  1. 01
    Licence categories

    Transport Victoria. Accessed 17 November 2026. Back

  2. 02
    Heavy vehicle and forklift licence categories

    Transport Victoria. Accessed 17 November 2026. Back

  3. 03
    How to get a heavy vehicle licence

    Transport Victoria. Accessed 17 November 2026. Back

  4. 04
    For commercial drivers

    Austroads. Accessed 17 November 2026. Back

  5. 05
  6. 06
    Guide to the Register of Approved Vehicles, June 2026, pages 6, 18 and 19

    Department of Infrastructure, Transport, Regional Development, Communications, Sport and the Arts. Accessed 17 November 2026. Back

  7. 07
    300 Series Alloy Tray Range, HSMY26BTGALLOYTRAY-0926, pages 2 to 4

    Hino Motor Sales Australia. Accessed 17 November 2026. Back

  8. 08
    Changes to Mass and Dimension Requirements, August 2026, pages 2 to 4

    National Heavy Vehicle Regulator. Accessed 17 November 2026. Back

  9. 09
    HVNL Industry Information Session: Fatigue and Fitness to Drive, May 2026

    National Heavy Vehicle Regulator. Accessed 17 November 2026. Back

  10. 10
  11. 11
    Master Code of Practice 2026

    National Heavy Vehicle Regulator. Accessed 17 November 2026. Back

  12. 12
    Insurance Contracts Act 1984, compilation 8 October 2026, section 54

    Federal Register of Legislation. Accessed 17 November 2026. Back

  13. 13
    Vehicle Standards Guide 9: Re-rating of Gross Vehicle Mass, revised July 2025

    National Heavy Vehicle Regulator. Accessed 17 November 2026. Back

  14. 14
    Vehicle assessment signatory scheme approval certificate

    Transport Victoria. Accessed 17 November 2026. Back

  15. 15
    GVM and GCM FAQs

    Transport WA. Accessed 17 November 2026. Back

  16. 16
    Heavy Vehicle National Law reform

    National Transport Commission. Accessed 17 November 2026. Back

  17. 17
    Finding vehicle details

    Queensland Department of Transport and Main Roads. Accessed 17 November 2026. Back

The information here is general. It doesn’t take your objectives, finances or needs into account, and it isn’t financial, legal or tax advice. Talk to us, and to your accountant, before you make a decision.

Got a question we haven’t answered?

Ask us a question

We’ll get back to you within 24 hours.